Devices You Need to Install a New Bath Tub
Devices You Need to Install a New Bath Tub
Blog Article
What're your thoughts concerning How to Install a Bathtub Yourself?
Installing a bath tub isn't precisely brain surgery, however it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough task. If the old tub is conveniently available, the task can relocate rapidly; if you need to open a wall surface to remove the old bathtub and position the brand-new bathtub, the job is much harder. In either case, the job is within a home handyman's skills, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. Make certain you have actually qualified on your own for the work and fit trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to consider using one before you begin. Opportunities are you might require a professional plumber to make tube connections.
This short article will certainly aid you install a new bath tub in your bathroom if you have already gotten a brand-new bathtub and don't require to alter the setup of your previous water supply pipes.
Your devices and also material list need to consist of the following:
Planning for the Installment
Firstly, the supporting framework supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets unit to prevent stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be fitted in its final position.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any kind of water staying in the system. The process of getting rid of the existing faucets can be quite bothersome because of the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, position the bathtub in the called for position. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub until the spirit level checks out degree.
To install faucets, fit the bottom of the outermost flexible tap port to the ideal supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Turn on the water system as well as check all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet and the typical electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bathtub ought to wait up until the bath tub has been utilized at the very least when as this will certainly settle it into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washers are in area between the faucet and also the sink. Secure the tap in position with the maker supplied backnut. As soon as the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The previous kind should be attached to the faucet finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, causing the water to pass through the wall surface between the bathroom and the tiling, leading to complications with wetness and also feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to allow for the activity experienced when the tub is in usage. The sealant can crack rather very early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently offered on the marketplace. It is a good idea to fit the floor tiles utilizing waterproof or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that article on Tools You Need to Install a New Bathtub when doing a lookup on the web. Sharing is nice. You never know, you may be doing someone a favor. Thank you so much for your time spent reading it.
Schedule Today!
Report this page